Home

3Pcs 12V 2 Channel Relay Module With Optocoupler Support High Low Level Trigger For Arduino

3Pcs 12V 2 Channel Relay Module With Optocoupler Support High Low Level Trigger For Arduino

Features: 1. The module uses genuine quality relay, normally open interfaces maximum load: AC 250V/10A, DC 30V/10A 2. Using SMD OPTOCOUPLER isolation, driving ability, stable performance; trigger current 5mA 3. The module voltage is 5V/9V/12 V/24V are available 4. The module can be set to high or low triggered by jumper 5. Fault-tolerant design, even if the control line is broken, the relay will not operate 6. The power indicator (green) relay status indicator (red) 7. Interface design humane, all interfaces can be connected directly via terminal wiring leads very convenient 8. Module size : 50mm * 40mm * 16mm (L * W * H) 9. Has four mounting bolts holes, hole 3.1mm Interface: 1. DC+: Positive power supply (voltage required by the relay, there 5V/9V/12V/24V choice ) 2. DC-: Negative power connection 3. IN1: 1 channel signal to trigger the end, you can set a high or low level control relay 3. IN2: 2 channel signal to trigger the end, you can set a high or low level control relay Outputs: NO1: After a relay normally open interfaces relay before floating, shorted pull with COM1 COM1: 1 relay common interface NC1: 1 relay normally closed port, COM1 relay shorted before and after the pull- vacant NO2: 2 -way normally open relay interface, the relay before floating, pull back and COM2 short COM2: 2 Common Interface relay NC2: 2 channel normally closed relay interface relay short front and COM2, pull vacant post High and low trigger selection: S1 as a relay trigger selection of high and low S2 high and low for the two -way relay trigger selection Comes with low short circuit, triggering the corresponding relay is low, while the high end of the short com high trigger High and low trigger selection: Short jumper with LOW triggered when connected When the jumper is high with high short trigger Package includes: 3 x 12V 2 channel relay driver module for arduino

Electronics/Audio

3Pcs 12V 2 Channel Relay Module With Optocoupler Support High Low Level Trigger For Arduino

12V 2 Channel Relay Module With Optocoupler Support High Low Level Trigger For Arduino

12V 2 Channel Relay Module With Optocoupler Support High Low Level Trigger For Arduino

Features: 1. The module uses genuine quality relay, normally open interfaces maximum load: AC 250V/10A, DC 30V/10A 2. Using SMD OPTOCOUPLER isolation, driving ability, stable performance; trigger current 5mA 3. The module voltage is 5V/9V/12 V/24V are available 4. The module can be set to high or low triggered by jumper 5. Fault-tolerant design, even if the control line is broken, the relay will not operate 6. The power indicator (green) relay status indicator (red) 7. Interface design humane, all interfaces can be connected directly via terminal wiring leads very convenient 8. Module size : 50mm * 40mm * 16mm (L * W * H) 9. Has four mounting bolts holes, hole 3.1mm Interface: 1. DC+: Positive power supply (voltage required by the relay, there 5V/9V/12V/24V choice ) 2. DC-: Negative power connection 3. IN1: 1 channel signal to trigger the end, you can set a high or low level control relay 3. IN2: 2 channel signal to trigger the end, you can set a high or low level control relay Outputs: NO1: After a relay normally open interfaces relay before floating, shorted pull with COM1 COM1: 1 relay common interface NC1: 1 relay normally closed port, COM1 relay shorted before and after the pull- vacant NO2: 2 -way normally open relay interface, the relay before floating, pull back and COM2 short COM2: 2 Common Interface relay NC2: 2 channel normally closed relay interface relay short front and COM2, pull vacant post High and low trigger selection: S1 as a relay trigger selection of high and low S2 high and low for the two -way relay trigger selection Comes with low short circuit, triggering the corresponding relay is low, while the high end of the short com high trigger High and low trigger selection: Short jumper with LOW triggered when connected When the jumper is high with high short trigger Package includes: 1 x 12V 2 channel relay driver module for arduino

Electronics/Audio

12V 2 Channel Relay Module With Optocoupler Support High Low Level Trigger For Arduino

5Pcs 12V 2 Channel Relay Module With Optocoupler Support High Low Level Trigger For Arduino

5Pcs 12V 2 Channel Relay Module With Optocoupler Support High Low Level Trigger For Arduino

Features: 1. The module uses genuine quality relay, normally open interfaces maximum load: AC 250V/10A, DC 30V/10A 2. Using SMD OPTOCOUPLER isolation, driving ability, stable performance; trigger current 5mA 3. The module voltage is 5V/9V/12 V/24V are available 4. The module can be set to high or low triggered by jumper 5. Fault-tolerant design, even if the control line is broken, the relay will not operate 6. The power indicator (green) relay status indicator (red) 7. Interface design humane, all interfaces can be connected directly via terminal wiring leads very convenient 8. Module size : 50mm * 40mm * 16mm (L * W * H) 9. Has four mounting bolts holes, hole 3.1mm Interface: 1. DC+: Positive power supply (voltage required by the relay, there 5V/9V/12V/24V choice ) 2. DC-: Negative power connection 3. IN1: 1 channel signal to trigger the end, you can set a high or low level control relay 3. IN2: 2 channel signal to trigger the end, you can set a high or low level control relay Outputs: NO1: After a relay normally open interfaces relay before floating, shorted pull with COM1 COM1: 1 relay common interface NC1: 1 relay normally closed port, COM1 relay shorted before and after the pull- vacant NO2: 2 -way normally open relay interface, the relay before floating, pull back and COM2 short COM2: 2 Common Interface relay NC2: 2 channel normally closed relay interface relay short front and COM2, pull vacant post High and low trigger selection: S1 as a relay trigger selection of high and low S2 high and low for the two -way relay trigger selection Comes with low short circuit, triggering the corresponding relay is low, while the high end of the short com high trigger High and low trigger selection: Short jumper with LOW triggered when connected When the jumper is high with high short trigger Package includes: 5 x 12V 2 channel relay driver module for arduino

Electronics/Audio

5Pcs 12V 2 Channel Relay Module With Optocoupler Support High Low Level Trigger For Arduino

10Pcs 12V 2 Channel Relay Module With Optocoupler Support High Low Level Trigger For Arduino

10Pcs 12V 2 Channel Relay Module With Optocoupler Support High Low Level Trigger For Arduino

Features: 1. The module uses genuine quality relay, normally open interfaces maximum load: AC 250V/10A, DC 30V/10A 2. Using SMD OPTOCOUPLER isolation, driving ability, stable performance; trigger current 5mA 3. The module voltage is 5V/9V/12 V/24V are available 4. The module can be set to high or low triggered by jumper 5. Fault-tolerant design, even if the control line is broken, the relay will not operate 6. The power indicator (green) relay status indicator (red) 7. Interface design humane, all interfaces can be connected directly via terminal wiring leads very convenient 8. Module size : 50mm * 40mm * 16mm (L * W * H) 9. Has four mounting bolts holes, hole 3.1mm Interface: 1. DC+: Positive power supply (voltage required by the relay, there 5V/9V/12V/24V choice ) 2. DC-: Negative power connection 3. IN1: 1 channel signal to trigger the end, you can set a high or low level control relay 3. IN2: 2 channel signal to trigger the end, you can set a high or low level control relay Outputs: NO1: After a relay normally open interfaces relay before floating, shorted pull with COM1 COM1: 1 relay common interface NC1: 1 relay normally closed port, COM1 relay shorted before and after the pull- vacant NO2: 2 -way normally open relay interface, the relay before floating, pull back and COM2 short COM2: 2 Common Interface relay NC2: 2 channel normally closed relay interface relay short front and COM2, pull vacant post High and low trigger selection: S1 as a relay trigger selection of high and low S2 high and low for the two -way relay trigger selection Comes with low short circuit, triggering the corresponding relay is low, while the high end of the short com high trigger High and low trigger selection: Short jumper with LOW triggered when connected When the jumper is high with high short trigger Package includes: 10 x 12V 2 channel relay driver module for arduino

Electronics/Audio

10Pcs 12V 2 Channel Relay Module With Optocoupler Support High Low Level Trigger For Arduino

BESTEP 1 Channel 12V Relay Module 30A With Optocoupler Isolation Support High And Low Level Trigger For Arduino

BESTEP 1 Channel 12V Relay Module 30A With Optocoupler Isolation Support High And Low Level Trigger For Arduino

Description: The module adopts high quality 30A relay, and the maximum load is normally open interface: AC 250V/30A, DC 30V/30A; The chip optocoupler isolation, strong driving ability, stable performance, trigger current 5mA; Module working voltage: 12V Can be set up by high jumper or low level trigger. Fault-tolerant design, the relay will not operate even if the control line is disconnected. Power indicator (green) relay status indicator (red) The interface design is humanized, all interfaces can be directly connected through the terminals, so it is very convenient. Module size: 50mm x 33mm x 24mm (length * width * height) Product net weight: 36g There are 4 fixed bolt holes, holes 3.1mm, spacing 44.5mm x 27.5mm Relay version: 12V Quiescent current: 5mA Maximum current: 190mA Trigger current: 2-4mA Module interface description: 1. DC+: module DC power supply positive pole (trigger terminal voltage positive). 2. DC-: module DC supply negative pole (trigger terminal voltage negative). 3. IN: signal trigger terminal (default trigger voltage is the same as power supply). 4. JD+: relay control terminal voltage positive pole 5. JD-: relay control terminal voltage negative pole 6. DC +/- and JD +/- uses jumper cap short connection, trigger terminal and relay control terminal voltage is the same. 7. Selection of high and low level trigger mode, when jumper is connected to L-terminal, IN-terminal is low level trigger, and H-terminal is high level trigger. 8. Normally closed terminal (NC): relay normally closed. 9. Public terminal (COM): common terminal of relay 10. Normally open terminal (NO): relay normally open. Package Included: 1 x 1 Channel 12V Relay Module

Electronics/Audio

BESTEP 1 Channel 12V Relay Module 30A With Optocoupler Isolation Support High And Low Level Trigger For Arduino

3Pcs 5V 1 Channel Level Trigger Optocoupler Relay Module For Arduino

3Pcs 5V 1 Channel Level Trigger Optocoupler Relay Module For Arduino

3Pcs 5V 1 Channel Level Trigger Optocoupler Relay Module For Arduino Description: The module uses genuine quality relay, normally open interfaces Using SMD optocoupler isolation, driving ability, stable performance The module can be high or low by a jumper setting trigger Fault-tolerant design, even if the control line is broken, the relay will not operate The power indicator (green) the relay status indicator (red) The interface design of human nature, all interfaces are available through a direct connection terminal leads, very convenient Specification: Maximum load: AC 250V/10A, DC 30V/10A Trigger current: 5mA Working voltage: 5V Module size: 50 x 26 x 18.5mm (L x W x H) Four mounting bolts holes, diameter 3.1mm Module interface: DC+: positive power supply (VCC) DC-: negative power supply (GND) IN: can be high or low level control relay Relay outputs: NO: normally open relay interface COM: Common Interface Relays NC: normally closed relay interface High and low level trigger options: It is low level trigger when jumper connect to LOW pin It is high level trigger when jumper connect to HIGH pin Package included: 3 x 1 Channel H/L level trigger optocoupler relay module

Electronics/Audio

3Pcs 5V 1 Channel Level Trigger Optocoupler Relay Module For Arduino

3pcs BESTEP 1 Channel 5V Relay Module 30A With Optocoupler Isolation Support High And Low Level Trigger For Arduino

3pcs BESTEP 1 Channel 5V Relay Module 30A With Optocoupler Isolation Support High And Low Level Trigger For Arduino

Description: The module adopts high quality 30A relay, and the maximum load is normally open interface: AC 250V/30A, DC 30V/30A; The chip optocoupler isolation, strong driving ability, stable performance, trigger current 5mA; Module working voltage: 5V Can be set up by high jumper or low level trigger. Fault-tolerant design, the relay will not operate even if the control line is disconnected. Power indicator (green) relay status indicator (red) The interface design is humanized, all interfaces can be directly connected through the terminals, so it is very convenient. Module size: 50mm x 33mm x 24mm (length * width * height) Product net weight: 36g There are 4 fixed bolt holes, holes 3.1mm, spacing 44.5mm x 27.5mm Relay version: 5V Quiescent current: 5mA Maximum current: 190mA Trigger current: 2-4mA Module interface description: 1. DC+: module DC power supply positive pole (trigger terminal voltage positive). 2. DC-: module DC supply negative pole (trigger terminal voltage negative). 3. IN: signal trigger terminal (default trigger voltage is the same as power supply). 4. JD+: relay control terminal voltage positive pole 5. JD-: relay control terminal voltage negative pole 6. DC +/- and JD +/- uses jumper cap short connection, trigger terminal and relay control terminal voltage is the same. 7. Selection of high and low level trigger mode, when jumper is connected to L-terminal, IN-terminal is low level trigger, and H-terminal is high level trigger. 8. Normally closed terminal (NC): relay normally closed. 9. Public terminal (COM): common terminal of relay 10. Normally open terminal (NO): relay normally open. Package Included: 3 x 1 Channel 5V Relay Module

Electronics/Audio

3pcs BESTEP 1 Channel 5V Relay Module 30A With Optocoupler Isolation Support High And Low Level Trigger For Arduino

BESTEP 1 Channel 24V Relay Module 30A With Optocoupler Isolation Support High And Low Level Trigger For Arduino

BESTEP 1 Channel 24V Relay Module 30A With Optocoupler Isolation Support High And Low Level Trigger For Arduino

Description: The module adopts high quality 30A relay, and the maximum load is normally open interface: AC 250V/30A, DC 30V/30A; The chip optocoupler isolation, strong driving ability, stable performance, trigger current 5mA; Module working voltage: 24V Can be set up by high jumper or low level trigger. Fault-tolerant design, the relay will not operate even if the control line is disconnected. Power indicator (green) relay status indicator (red) The interface design is humanized, all interfaces can be directly connected through the terminals, so it is very convenient. Module size: 50mm x 33mm x 24mm (length * width * height) Product net weight: 36g There are 4 fixed bolt holes, holes 3.1mm, spacing 44.5mm x 27.5mm Relay version: 24V Quiescent current: 5mA Maximum current: 190mA Trigger current: 2-4mA Module interface description: 1. DC+: module DC power supply positive pole (trigger terminal voltage positive). 2. DC-: module DC supply negative pole (trigger terminal voltage negative). 3. IN: signal trigger terminal (default trigger voltage is the same as power supply). 4. JD+: relay control terminal voltage positive pole 5. JD-: relay control terminal voltage negative pole 6. DC +/- and JD +/- uses jumper cap short connection, trigger terminal and relay control terminal voltage is the same. 7. Selection of high and low level trigger mode, when jumper is connected to L-terminal, IN-terminal is low level trigger, and H-terminal is high level trigger. 8. Normally closed terminal (NC): relay normally closed. 9. Public terminal (COM): common terminal of relay 10. Normally open terminal (NO): relay normally open. Package Included: 1 x 1 Channel 12V Relay Module

Electronics/Audio

BESTEP 1 Channel 24V Relay Module 30A With Optocoupler Isolation Support High And Low Level Trigger For Arduino

BESTEP 1 Channel 5V Relay Module 30A With Optocoupler Isolation Support High And Low Level Trigger For Arduino

BESTEP 1 Channel 5V Relay Module 30A With Optocoupler Isolation Support High And Low Level Trigger For Arduino

Description: The module adopts high quality 30A relay, and the maximum load is normally open interface: AC 250V/30A, DC 30V/30A; The chip optocoupler isolation, strong driving ability, stable performance, trigger current 5mA; Module working voltage: 5V Can be set up by high jumper or low level trigger. Fault-tolerant design, the relay will not operate even if the control line is disconnected. Power indicator (green) relay status indicator (red) The interface design is humanized, all interfaces can be directly connected through the terminals, so it is very convenient. Module size: 50mm x 33mm x 24mm (length * width * height) Product net weight: 36g There are 4 fixed bolt holes, holes 3.1mm, spacing 44.5mm x 27.5mm Relay version: 5V Quiescent current: 5mA Maximum current: 190mA Trigger current: 2-4mA Module interface description: 1. DC+: module DC power supply positive pole (trigger terminal voltage positive). 2. DC-: module DC supply negative pole (trigger terminal voltage negative). 3. IN: signal trigger terminal (default trigger voltage is the same as power supply). 4. JD+: relay control terminal voltage positive pole 5. JD-: relay control terminal voltage negative pole 6. DC +/- and JD +/- uses jumper cap short connection, trigger terminal and relay control terminal voltage is the same. 7. Selection of high and low level trigger mode, when jumper is connected to L-terminal, IN-terminal is low level trigger, and H-terminal is high level trigger. 8. Normally closed terminal (NC): relay normally closed. 9. Public terminal (COM): common terminal of relay 10. Normally open terminal (NO): relay normally open. Package Included: 1 x 1 Channel 5V Relay Module

Electronics/Audio

BESTEP 1 Channel 5V Relay Module 30A With Optocoupler Isolation Support High And Low Level Trigger For Arduino

10pcs BESTEP 1 Channel 5V Relay Module 30A With Optocoupler Isolation Support High And Low Level Trigger For Arduino

10pcs BESTEP 1 Channel 5V Relay Module 30A With Optocoupler Isolation Support High And Low Level Trigger For Arduino

Description: The module adopts high quality 30A relay, and the maximum load is normally open interface: AC 250V/30A, DC 30V/30A; The chip optocoupler isolation, strong driving ability, stable performance, trigger current 5mA; Module working voltage: 5V Can be set up by high jumper or low level trigger. Fault-tolerant design, the relay will not operate even if the control line is disconnected. Power indicator (green) relay status indicator (red) The interface design is humanized, all interfaces can be directly connected through the terminals, so it is very convenient. Module size: 50mm x 33mm x 24mm (length * width * height) Product net weight: 36g There are 4 fixed bolt holes, holes 3.1mm, spacing 44.5mm x 27.5mm Relay version: 5V Quiescent current: 5mA Maximum current: 190mA Trigger current: 2-4mA Module interface description: 1. DC+: module DC power supply positive pole (trigger terminal voltage positive). 2. DC-: module DC supply negative pole (trigger terminal voltage negative). 3. IN: signal trigger terminal (default trigger voltage is the same as power supply). 4. JD+: relay control terminal voltage positive pole 5. JD-: relay control terminal voltage negative pole 6. DC +/- and JD +/- uses jumper cap short connection, trigger terminal and relay control terminal voltage is the same. 7. Selection of high and low level trigger mode, when jumper is connected to L-terminal, IN-terminal is low level trigger, and H-terminal is high level trigger. 8. Normally closed terminal (NC): relay normally closed. 9. Public terminal (COM): common terminal of relay 10. Normally open terminal (NO): relay normally open. Package Included: 10 x 1 Channel 5V Relay Module

Electronics/Audio

10pcs BESTEP 1 Channel 5V Relay Module 30A With Optocoupler Isolation Support High And Low Level Trigger For Arduino

5pcs BESTEP 1 Channel 5V Relay Module 30A With Optocoupler Isolation Support High And Low Level Trigger For Arduino

5pcs BESTEP 1 Channel 5V Relay Module 30A With Optocoupler Isolation Support High And Low Level Trigger For Arduino

Description: The module adopts high quality 30A relay, and the maximum load is normally open interface: AC 250V/30A, DC 30V/30A; The chip optocoupler isolation, strong driving ability, stable performance, trigger current 5mA; Module working voltage: 5V Can be set up by high jumper or low level trigger. Fault-tolerant design, the relay will not operate even if the control line is disconnected. Power indicator (green) relay status indicator (red) The interface design is humanized, all interfaces can be directly connected through the terminals, so it is very convenient. Module size: 50mm x 33mm x 24mm (length * width * height) Product net weight: 36g There are 4 fixed bolt holes, holes 3.1mm, spacing 44.5mm x 27.5mm Relay version: 5V Quiescent current: 5mA Maximum current: 190mA Trigger current: 2-4mA Module interface description: 1. DC+: module DC power supply positive pole (trigger terminal voltage positive). 2. DC-: module DC supply negative pole (trigger terminal voltage negative). 3. IN: signal trigger terminal (default trigger voltage is the same as power supply). 4. JD+: relay control terminal voltage positive pole 5. JD-: relay control terminal voltage negative pole 6. DC +/- and JD +/- uses jumper cap short connection, trigger terminal and relay control terminal voltage is the same. 7. Selection of high and low level trigger mode, when jumper is connected to L-terminal, IN-terminal is low level trigger, and H-terminal is high level trigger. 8. Normally closed terminal (NC): relay normally closed. 9. Public terminal (COM): common terminal of relay 10. Normally open terminal (NO): relay normally open. Package Included: 5 x 1 Channel 5V Relay Module

Electronics/Audio

5pcs BESTEP 1 Channel 5V Relay Module 30A With Optocoupler Isolation Support High And Low Level Trigger For Arduino

5Pcs 12V 2 Channel Relay Module With Optocoupler Support High Low Level Trigger For Arduino

5Pcs 12V 2 Channel Relay Module With Optocoupler Support High Low Level Trigger For Arduino

Features: 1. The module uses genuine quality relay, normally open interfaces maximum load: AC 250V/10A, DC 30V/10A 2. Using SMD OPTOCOUPLER isolation, driving ability, stable performance; trigger current 5mA 3. The module voltage is 5V/9V/12 V/24V are available 4. The module can be set to high or low triggered by jumper 5. Fault-tolerant design, even if the control line is broken, the relay will not operate 6. The power indicator (green) relay status indicator (red) 7. Interface design humane, all interfaces can be connected directly via terminal wiring leads very convenient 8. Module size : 50mm * 40mm * 16mm (L * W * H) 9. Has four mounting bolts holes, hole 3.1mm Interface: 1. DC+: Positive power supply (voltage required by the relay, there 5V/9V/12V/24V choice ) 2. DC-: Negative power connection 3. IN1: 1 channel signal to trigger the end, you can set a high or low level control relay 3. IN2: 2 channel signal to trigger the end, you can set a high or low level control relay Outputs: NO1: After a relay normally open interfaces relay before floating, shorted pull with COM1 COM1: 1 relay common interface NC1: 1 relay normally closed port, COM1 relay shorted before and after the pull- vacant NO2: 2 -way normally open relay interface, the relay before floating, pull back and COM2 short COM2: 2 Common Interface relay NC2: 2 channel normally closed relay interface relay short front and COM2, pull vacant post High and low trigger selection: S1 as a relay trigger selection of high and low S2 high and low for the two -way relay trigger selection Comes with low short circuit, triggering the corresponding relay is low, while the high end of the short com high trigger High and low trigger selection: Short jumper with LOW triggered when connected When the jumper is high with high short trigger Package includes: 5 x 12V 2 channel relay driver module for arduino

Electronics/Audio

5Pcs 12V 2 Channel Relay Module With Optocoupler Support High Low Level Trigger For Arduino

GY-2561 TSL2561 Luminosity Sensor Breakout Infrared Light Sensor Module Integrating Sensor AL

GY-2561 TSL2561 Luminosity Sensor Breakout Infrared Light Sensor Module Integrating Sensor AL

Description: The TSL2561 Luminosity Sensor Breakout is a sophisticated light sensor which has a flat response across most of the visible spectrum. Unlike simpler sensors, the TSL2561 measures both infrared and visible light to better approximate the response of the human eye. And because the TSL2561 is an integrating sensor (it soaks up light for a predetermined amount of time) it is capable of measuring both small and large amounts of light by changing the integration time. The TSL2561 is capable of direct I2C communication and is able to conduct specific light ranges from 0.1 - 40k+ Lux easily. Additionally, the TSL12561 contains two integrating analog-to-digital converters (ADC) that integrate currents from two photodiodes, simultaneously. Each breakout requires a supply voltage of 3V and a low supply current max of 0.6mA. Package included: 1 x GY-2561 TSL2561 Luminosity Sensor

Electronics/Audio

GY-2561 TSL2561 Luminosity Sensor Breakout Infrared Light Sensor Module Integrating Sensor AL

D213 Opto-isolator ILD213T Breakout Module Optoisolator Microcontroller Board For Arduino

D213 Opto-isolator ILD213T Breakout Module Optoisolator Microcontroller Board For Arduino

Feature: The Opto-isolator Breakout Board which uses the ILD213T optoisolator and discrete transistors to correct the logic. Comes with two channels can help you to connect digital systems (like a 5V microcontroller) to a high-voltage or noisy system. It electrically isolates a controller from the high-power system by use of an opto-isolator IC. This IC has two LEDs and two photodiodes built-in. This allows the low-voltage side to control a high voltage side. This board will isolate the systems, creating a type of electrical noise barrier between devices. You can use this board to allow a microcontroller control servos or other motors that use a higher voltage than the TTL logic on the (3.3V or 5V) micro, and may cause electromagnetic interferance with our system as the motors turn on and off. Package includes: 1 x D213 Opto-isolator Breakout

Electronics/Audio

D213 Opto-isolator ILD213T Breakout Module Optoisolator Microcontroller Board For Arduino

GY-9960-3.3 APDS-9960 RGB Infrared IR Gesture Sensor Motion Direction Recognition Module For Arduino

GY-9960-3.3 APDS-9960 RGB Infrared IR Gesture Sensor Motion Direction Recognition Module For Arduino

Description: This is the RGB and Gesture Sensor, a small breakout board with a built in APDS-9960 sensor that offers ambient light and color measuring, proximity detection, and touchless gesture sensing. With this RGB and Gesture Sensor you will be able to control a computer, microcontroller, robot, and more with a simple swipe of your hand. This is, in fact, the same sensor that the Samsung Galaxy S5 uses and is probably one of the best gesture sensors on the market for the price. The APDS-9960 is a serious little piece of hardware with built in UV and IR blocking filters, four separate diodes sensitive to different directions, and an I2C compatible interface. For your convenience we have broken out the following pins: VL (optional power to IR LED) GND (Ground) VCC (power to APDS-9960 sensor) SDA (I2C data) SCL (I2C clock) and INT (interrupt). Each APDS-9960 also has a detection range of 4 to 8 inches (10 to 20 cm). Features: Model: GY-APDS 9960-3.3 Using chip: APDS-9960 Power supply: 3.3v Communication: IIC communication protocol Size: 20mm * 15.3mm Package included: 1 x RGB Infrared IR Gesture Sensor

Electronics/Audio

GY-9960-3.3 APDS-9960 RGB Infrared IR Gesture Sensor Motion Direction Recognition Module For Arduino

10pcs GY-9960-3.3 APDS-9960 RGB Infrared IR Gesture Sensor Motion Direction Recognition Module For Arduino

10pcs GY-9960-3.3 APDS-9960 RGB Infrared IR Gesture Sensor Motion Direction Recognition Module For Arduino

Description: This is the RGB and Gesture Sensor, a small breakout board with a built in APDS-9960 sensor that offers ambient light and color measuring, proximity detection, and touchless gesture sensing. With this RGB and Gesture Sensor you will be able to control a computer, microcontroller, robot, and more with a simple swipe of your hand. This is, in fact, the same sensor that the Samsung Galaxy S5 uses and is probably one of the best gesture sensors on the market for the price. The APDS-9960 is a serious little piece of hardware with built in UV and IR blocking filters, four separate diodes sensitive to different directions, and an I2C compatible interface. For your convenience we have broken out the following pins: VL (optional power to IR LED) GND (Ground) VCC (power to APDS-9960 sensor) SDA (I2C data) SCL (I2C clock) and INT (interrupt). Each APDS-9960 also has a detection range of 4 to 8 inches (10 to 20 cm). Features: Model: GY-APDS 9960-3.3 Using chip: APDS-9960 Power supply: 3.3v Communication: IIC communication protocol Size: 20mm * 15.3mm Package included: 10 x RGB Infrared IR Gesture Sensor

Electronics/Audio

10pcs GY-9960-3.3 APDS-9960 RGB Infrared IR Gesture Sensor Motion Direction Recognition Module For Arduino

5Pcs Mini IR Pyroelectric Infrared PIR Sensor Detector Module

5Pcs Mini IR Pyroelectric Infrared PIR Sensor Detector Module

5Pcs Mini IR Pyroelectric Infrared PIR Sensor Detector Module Description : The module can accurately detect any moving objects (e.g. human body) within the detective range and will send out signals of high level for a certain time. It has higher sensitivity and broader detective range than others. Completely automatic induction: once a person enters into the detective range, the output is high level. While the person is out of the detective range, it will prolong automatically 20 seconds of retention time then the high level output will be shifted to the low level output. Triggering method: continuous triggering, which means that it will take the last triggering time as the starting point, within 20 seconds of the high level output, if there's still human beings activities within it's detective zone, the output will be maintained in the high level until the person's leave. Then afterwards, a retention time of 20 seconds will be initiated. Broad working voltage, low power consumption. High level signal output, easy to be butt jointed with different types of circuits. The module is widely accepted and has been applied for : movement detection, automatic control, proximity switch, electronic theft prevention, safety protection, remote control measurement. Specifications: Operating temperature range: -20~+70 Working voltage: DC 5V~9V Working current: 5mA Static current:

Electronics/Audio

5Pcs Mini IR Pyroelectric Infrared PIR Sensor Detector Module

10pcs Pulsesensor Pulse Heart Rate Sensor Module For Arduino Pulse Sensor

10pcs Pulsesensor Pulse Heart Rate Sensor Module For Arduino Pulse Sensor

Description: The pulse sensor is a sensor used to test the heart rate. Students, artists, athletes, creators, games or mobile terminal developers can develop interactive works related to heart rate. The sensor can be worn on a finger or earlobe and connected to the Ard via a wire. It also has an open source app that displays your heart rate in real time. The essence is an optical heart rate sensor that integrates an amplifying circuit and a noise canceling circuit. Supply voltage: 3V or 5V. Package included: 10 x Pulsesensor Pulse Heart Rate Sensor Module

Electronics/Audio

10pcs Pulsesensor Pulse Heart Rate Sensor Module For Arduino Pulse Sensor

3pcs Mini IR Pyroelectric Infrared PIR Motion Human Sensor Detector Module

3pcs Mini IR Pyroelectric Infrared PIR Motion Human Sensor Detector Module

Description : The module can accurately detect any moving objects (e.g. human body) within the detective range and will send out signals of high level for a certain time. It has higher sensitivity and broader detective range than others. Completely automatic induction: once a person enters into the detective range, the output is high level. While the person is out of the detective range, it will prolong automatically 20 seconds of retention time then the high level output will be shifted to the low level output. Triggering method: continuous triggering, which means that it will take the last triggering time as the starting point, within 20 seconds of the high level output, if there's still human beings activities within it's detective zone, the output will be maintained in the high level until the person's leave. Then afterwards, a retention time of 20 seconds will be initiated. Broad working voltage, low power consumption. High level signal output, easy to be butt jointed with different types of circuits. The module is widely accepted and has been applied for : movement detection, automatic control, proximity switch, electronic theft prevention, safety protection, remote control measurement. Specifications: Operating temperature range: -20~+70 Working voltage: DC 5V~9V Working current: 5mA Static current:

Electronics/Audio

3pcs Mini IR Pyroelectric Infrared PIR Motion Human Sensor Detector Module

3pcs GY-9960-3.3 APDS-9960 RGB Infrared IR Gesture Sensor Motion Direction Recognition Module For Arduino

3pcs GY-9960-3.3 APDS-9960 RGB Infrared IR Gesture Sensor Motion Direction Recognition Module For Arduino

Description: This is the RGB and Gesture Sensor, a small breakout board with a built in APDS-9960 sensor that offers ambient light and color measuring, proximity detection, and touchless gesture sensing. With this RGB and Gesture Sensor you will be able to control a computer, microcontroller, robot, and more with a simple swipe of your hand. This is, in fact, the same sensor that the Samsung Galaxy S5 uses and is probably one of the best gesture sensors on the market for the price. The APDS-9960 is a serious little piece of hardware with built in UV and IR blocking filters, four separate diodes sensitive to different directions, and an I2C compatible interface. For your convenience we have broken out the following pins: VL (optional power to IR LED) GND (Ground) VCC (power to APDS-9960 sensor) SDA (I2C data) SCL (I2C clock) and INT (interrupt). Each APDS-9960 also has a detection range of 4 to 8 inches (10 to 20 cm). Features: Model: GY-APDS 9960-3.3 Using chip: APDS-9960 Power supply: 3.3v Communication: IIC communication protocol Size: 20mm * 15.3mm Package included: 3 x RGB Infrared IR Gesture Sensor

Electronics/Audio

3pcs GY-9960-3.3 APDS-9960 RGB Infrared IR Gesture Sensor Motion Direction Recognition Module For Arduino

3pcs GY-68 300-1100hPa BMP180 BOSCH Temperature Module Atmospheric Pressure Sensor Instead Of BMP085 High Precision Low Energy Consumption Temperature Output 8-Pin LCC I2C Interface Lead Free

3pcs GY-68 300-1100hPa BMP180 BOSCH Temperature Module Atmospheric Pressure Sensor Instead Of BMP085 High Precision Low Energy Consumption Temperature Output 8-Pin LCC I2C Interface Lead Free

Description: BMP180 is a high precision, small size, low energy consumption pressure sensor. It can be used in mobile devices. Its performance is excellent, the absolute accuracy can achieve 0.03hPa (minimum) and low power consumption, only 3A. The BMP180 uses a powerful 8-pin ceramic leadless chip carrier (LCC) ultra thin package that can be directly connected to various microprocessors via the I2C bus. Features: Pressure range: 300~1100hPa (elevation of 9000 meters to -500 meters) Power supply voltage: 1.8V~3.6V (VDDA) 1.62V~3.6V (VDDD) LCC8 package: leadless ceramic carrier package (LCC) Size: 3.6 x 3.8 x 0.93mm Low power consumption: 5A in standard mode High precision: low power mode, the resolution of 0.06hPa (0.5m) In high linear mode, the resolution is 0.03hPa (0.25m) Temperature output I2C interface Temperature compensation Lead free, comply with RoHS specification MSL 1 reaction time: 7.5ms Standby current: 0.1 A No external clock circuit is required Typical applications: GPS accurate navigation (dead reckoning, upper and lower bridge detection etc.) Indoor and outdoor navigation Leisure, sports and health care and other monitoring Weather forecast Vertical speed indicator (rising / sinking speed) Fan power control Package included: 3 x GY-68 300-1100hPa BMP180 BOSCH temperature module

Electronics/Audio

3pcs GY-68 300-1100hPa BMP180 BOSCH Temperature Module Atmospheric Pressure Sensor Instead Of BMP085 High Precision Low Energy Consumption Temperature Output 8-Pin LCC I2C Interface Lead Free